2025 Caterpillar Large Wheel Loaders 995

Information

2025 Caterpillar Large Wheel Loaders 995

Same Size, More Payload

Built to the same size as the 994K but offering a higher rated payload, the new Cat® 995 Wheel Loader gives you greater productivity and performance while using less fuel. It offers a one-pass reduction when loading Cat 785, 789 and 793 Mining Trucks — increasing production and efficiency up to 33% when loading the 785, up to 25% when loading the 789, and up to 20% with the 793. The 995 demonstrates 21% higher efficiency and 24% more production than the 994K in equal operating mode thanks to a higher rated payload and 6% increase in hydraulic force. In Enhanced Eco Mode, the 995 demonstrates up to a 30% increase in efficiency and an 11% reduction in hourly fuel consumption versus the 994K in throttle lock mode, which translates to 23% less CO2 per unit of material moved. It also offers a more comfortable operator environment and is infused with new technology features that allow additional gains in efficiency.

BenefitsUp to 24% More Productive

With higher rated payload, 6% increase in hydraulic force and equal hydraulic cycle time vs. 994K

Up to 21% More Efficient

17% less CO2 per unit of material moved versus 994K in equal operating mode (throttle lock)

Confident & Empowered Operators

Thanks to options like Tire Slip Prevention, Lift Stall Prevention, Tire Set, Operator Coaching and more

Features may include:

Safety
  • Improved access and egress, with integrated powered access system that can be raised and lowered from cab or ground, 45-degree-angle wide stairs, emergency egress ladder, and full handrails on each side.
Operator Comfort
  • Increased leg room and increased width by the operator’s knees compared to 994K.
  • Reduced vibration, low sound levels and automatic temperature controls.
  • Electro-hydraulic speed-sensing steering with force feedback for shift-long comfort.
Productivity
  • Increased rated payload and 6% increase in hydraulic force compared to 994K.
  • Impeller Clutch Torque Converter (ICTC) and Rimpull Control System (RCS), which reduce the potential for wheel slippage without reducing hydraulic efficiency.
  • Superior loading with Cat Performance Series Buckets, which are engineered to dig into piles quickly and load efficiently — with fill factors up to 115%.
Serviceability
  • Reduced time spent on regular maintenance procedures thanks to features such as ground-level or platform access to filters; grouped service points; swing-out doors on both sides of the engine compartment; improved access for engine and pump drive service as well as to cooling package; and automatic lubrication system that greases the linkage, hitch, steering and axle trunnion bearings.
  • Service station that provides easy access to functions such as coolant and oil as well as level indicators; Cat battery charging connector; and indicator lights for full fuel tanks.
  • Redesigned pump bay, which offers improved access to transmission components, discharge ports located on the side of pumps, and lines routed directly to screen.
Durability
  • Highly durable structures, with full box-section rear frame that resists torsional shock and twisting forces to maximize life of mounted components.
  • Frames that utilize castings in key areas to maximize frame durability and optimize efficiency.

Photos

Highlights

  • San Diego, California
  • 2025
  • Caterpillar
  • Large Wheel Loaders 995
  • Model: Cat® 3516E
  • Cat Planetary Power Shift
  • Available
  • Standard Lift Over Tires - With Bulge: 18.8 ft| Standard Lift Tread: 14.1 ft | High Lift Over Tires - With Bulge: 18.8 | High Lift Tread: 14.1 ft
  • High Lift B-Pin Height at Maximum Lift: 31.6 ft | Standard Lift B-Pin Maximum: 28.8 ft

Specifications

  • 2025
  • Caterpillar
  • Large Wheel Loaders
  • 995
  • Large
  • Model: Cat® 3516E
  • Engine Power - ISO 14396: 2002: 1847 hp | Gross Power - SAE J1995:2014: 1870 hp | Net Power - SAE J1349 - Standard Ambient: 1739 hp | Net Power - SAE J1349 - High Ambient: 1696 hp
  • 1750 rpm
  • Peak - 1,200 rpm - SAE J1995: 8549 lb/ft
  • 6.7 in
  • 8.5 in
  • 4766 in³
  • U.S. EPA Tier 4 Final/EU Stage V or U.S. EPA Tier 1 equivalent
  • 39%
  • Cat Planetary Power Shift
  • Forward - 1: 4.6 mile/h | Direct Drive - Forward 1: Lock-up disables
  • Forward - 2: 8 mile/h | Direct Drive - Forward 2: 8.7 mile/h
  • Forward - 3: 13.6 mile/h | Direct Drive - Forward 3: 15.2 mile/h
  • Reverse - 1: 5 mile/h | Reverse - 2: 8.8 mile/h | Reverse - 3: 14.9 mile/h | Direct Drive - Reverse 1: Lock-up disables | Direct Drive - Reverse 2: 9.6 mile/h | Direct Drive - Reverse 3: 16.8 mile/h
  • System - Circuit: Pilot, Load Sensing | System - Pump: Piston, variable displacement | Total Angle: 80 degrees
  • Final Drives: 220 gal (US)
  • Final Drives: 200 gal (US)
  • ISO 3450:2011
  • Rack Back 4.9 s | Raise: 12.6 s | Dump: 3.1 s | Lower Float Down: 4.2 s | Steering - Low Idle: 7.6 s | Steering - High Idle: 4.3 s
  • Operator Sound Level (ISO 6396:2008) - Tier 1/EU Stage I Equivalent: 74 dB(A) | Machine Sound Level (ISO 6395:2008): 119 dB(A) | Operator Sound Level (ISO 6396:2008) - Tier 1/EU Stage I Equivalent: 73 dB(A) | Machine Sound Level (ISO 6395:2008): 117 dB(A)
  • Maximum Flow at 1,700 rpm Engine Speed: 541 gal/min
  • Tank - Implement and Hydraulic Fan: 270 gal (US) | Tank - Steering and Braking: 100 gal (US)
  • Lift/Tilt: 5004 psi
  • High Lift Ground to Top of ROPS: 23.4 ft | High Lift Ground to Top of Exhaust Stacks: 23.2 ft | High Lift Ground to Top of Hood: 18.6 ft | High Lift Ground to Center of Axles: 6 ft | High Lift Rack Back Angle - carry: 53.5 degrees | High Lift Dump Angle at Maximum: -50 degrees | Standard Lift Dump Angle at Maximum: -50 degrees | Standard Lift Rack Angle at Maximum: 56.5 degrees | High Lift Rack Back Angle - Ground Level: 45 degrees | Standard Lift Rack Back Angle - Carry: 47.7 degrees | High Lift Front Axle Centerline to Bucket Tip: 24.2 ft | High Lift Rear Axle - Centerline to Bumper: 20.4 ft | Standard Lift Rear Axle CenterLine to Bumper: 20.4 ft | High Lift Clearance at Maximum: 22.6 ft | High Lift Reach - Maximum: 9.4 ft | Standard Lift Front Axle Centerline to Bucket Tip: 21.9 ft | Standard Lift Reach - Maximum: 9.6 ft | Standard Lift Clearance at Maximum: 19.8 ft | Oscillation Angle: 9° | Standard Lift Ground to Top of ROPS: 23.4 ft | Standard Lift Ground to Top of Exhaust Stacks: 23.2 ft | Standard Lift Ground to Top of Hood: 18.6 ft | Standard Lift Ground to Center of Axles: 6 ft | High Lift Rack Back Angle - Ground Level: 45 degrees | High Lift Rack Angle at Maximum: 59.4 degrees | Standard Lift Rack Back Angle - Ground Level: 39.7 degrees | Cylinders, Double Acting - Lift, Bore and Stroke: 370 × 1713 mm (14.6 × 67.4 in) | Cylinders, Double Acting - Tilt, Bore and Stroke: 310 × 1086 mm (12.2 × 42.8 in) |
  • High Lift B-Pin Height at Maximum Lift: 31.6 ft | Standard Lift B-Pin Maximum: 28.8 ft
  • Standard Lift Over Tires - With Bulge: 18.8 ft| Standard Lift Tread: 14.1 ft | High Lift Over Tires - With Bulge: 18.8 | High Lift Tread: 14.1 ft
  • Standard Lift Maximum - Bucket Raised: 39.3 ft | High Lift Maximum - Bucket Raised: 42.1 ft
  • Standard Lift Maximum: 64.6 ft | High Lift Maximum: 66.9 ft
  • Standard Lift To Bumper: 4.4 ft | Standard Lift To Lower Hitch: 2.9 ft | High Lift To Bumper: 4.4 ft | High Lift To Lower Hitch: 2.9 ft
  • Standard Lift / High Lift: 22.3 ft
  • Tank Standard: 856 gal (US) (US) | Tank - With 24 hr Attachment: 1414 gal (US)
  • Rated - Standard Lift (Low to Moderate Digging Resistance): 60 ton (US) | Rated - Standard Lift (Moderate to High Digging Resistance): 50 ton (US) | Rated - High Lift (Low to Moderate Digging Resistance): 55 ton (US) | Rated - High Lift (Moderate to High Digging Resistance): 50 ton (US)
  • Renewal System (ORS): 20 gal (US)
  • Pilot System: Open Loop and Pressure Reducing | Axles Front: Fixed | Rear: Trunnion | Cat Truck Match - Standard: 785/789 | Cat Truck Match - High Lift: 789/793/794
  • 138 gal (US) | Ambient Capability Hydraulically Driven Demand Fan - Standard: 109.4 °F | Ambient Capability Hydraulically Driven Demand Fan - High (Tier 1 equivalent): 131 °F | Ambient Capability Hydraulically Driven Demand Fan - High (Tier 4 Final): 127.4 °F
  • Bucket Capacity Range: 17.2-43.6 m3 (22.3-57 yd3)
  • Operating Standard: 543772 lb | Operating High Lift: 547675 lb
  • Lift/Tilt System - Circuit: Positive flow control | Lift/Tilt System - Pump: Variable displacement piston